Electronics Forum | Fri Sep 08 21:49:24 EDT 2017 | sbar5781
Hello, I have a few PCB boards i am trying to be manufactured that are miniaturized medical devices. Thus they require IPC Class 3 Specs. However as miniature devices they have limited space, including a 0.4mm pitch BGA socket, which currently has
Electronics Forum | Tue Jul 31 15:29:45 EDT 2001 | hinerman
Research was done into the deflection of a totally unsupported (topside) PCB of 0.050" thickness. A dial indicator was placed on the surface and the tooling was set. The deflection ranged from 0.005" to 0.007". This is minor when you consider th
Electronics Forum | Wed Jan 05 11:01:37 EST 2000 | Ron Lahat
I have in design a 400mm x 400mm pcb 3.0 mm thick heavily populated with BGAs 50 mil pitch and want to run a double sided reflow process with overlapping BGAs (CS/PS) 1. can I avoid a selective jig for PS BGAs?(weight calculation ?) 2. Is it possibl
Electronics Forum | Mon Jun 15 06:21:13 EDT 2020 | ameenullakhan
Hi Team, Main reason for HIP are; 1. Warpage in component or PCB : Verified the part and PCB 1.6 mm thickness no warpage found. 2. Hip was at different locations : center as well as corner : So not because of warpage of component. 3.Solder paste equ
Electronics Forum | Fri Dec 01 00:30:59 EST 2000 | arminski
I have a proto-type PCB with a 48-Pin Fine Pitch TSOP (0.5mm pitch) with a dimension of 19mm L x 11.50mm W x 1.10 Thickness. They are at the bottomside of the PCB and I need to wave solder the board. There are 8 of them at the bottom side. Are they o
Electronics Forum | Mon Jul 30 18:52:43 EDT 2001 | Brian W.
You did not provide the stencil thickness or your aspect ratio. If your aspect ratio (Aperture width/stencil thickness) is less than 1.5, the paste will not release correctly from the aperture, leaving paste in the aperture. For example, if your pa
Electronics Forum | Wed Jan 16 15:22:29 EST 2002 | Terry Burnette
In his book titled "Manufacturing Techniques for Surface Mount Assemblies" author R.J. Klein Wassink describes the relationship between solder land dimensions, component lead coplanarity, board warpage, solder volumes, and solder paste flux wetting b
Electronics Forum | Thu Oct 05 10:37:10 EDT 2006 | David
Hello all, We have problem with voids in one of our product. We are soldering IC (package SO8) with under the components grounding connection. The ground pad for this component has 3 via holes (before producing we have to cover this 3 holes from b
Electronics Forum | Mon Aug 23 03:12:57 EDT 2010 | grahamcooper22
Possible route causes of bridging on fine pitch ICs are; too much paste (stencil aperture wrong), poor print quality (paste smudges during printing), pcb pads not flat depending on the solderable coating, paste has poor cold slump properties, too muc
Electronics Forum | Wed Jun 28 12:29:59 EDT 2000 | Christopher Lampron
Does anyone know what the min-max plating thickness for HASL is? Is there a specification that defines this requirement? We have had problems with PCB's that have excessive solder plating on the pads. This wreaks havok with our QFP's. Any help would
Products, services, training & consulting for the assembly, rework & repair of electronic assemblies. BGA process experts. Manufacturers Rep, Distributor & Service Provider for Seamark/Zhuomao and Shuttle Star BGA Rework Stations.
Training Provider / Manufacturer's Representative / Equipment Dealer / Broker / Auctions / Consultant / Service Provider
1750 Mitchell Ave.
Oroville, CA USA
Phone: (888) 406-2830
.gif)
